Penyerahan Naskah

Panduan Penulis

The Pasca Teknik Sipil (S2) Unsrat Open Journal System (PTSU-OJS) consist of Jurnal Ilmiah Media Engineering (Online Not Yet) and Jurnal Ilmiah Media Engineering (Print) are published fourannualy, in Februari, March, July and November, by Pasca Teknik Sipil (S2) Sam Ratulangi University

PTSU-OJS aims to:

1. Promote a civil engineering incorporating viewpoints of different disciplines.
2. Elaborate and strengthen academic exchange with other institutions.
3. Support scientist, practicing engineers, and others to conduct research and other similar activities.

PTSU-OJS welcomes papers with the above aims and scopes. The editorial board decides papers to be published in PTSU-OJS journal after review by reviewers appointed by the board. Authors will be advised of reviewers' comments and suggestions.

Submission and Correspondence
Author shall submit paper by email to fabian_jm@unsrat.ac.id. File shall be named as follows: first three letters shall be followed by the first name of the first author and first word of the title, i.e.: ptsu-ojs(o/p)-fabian-composite. (o for online and p for print

Papers and all correspondences should be addressed to:
The Editor, Media Engineering Journal.
Pasca Sarjana Teknik Sipil (S2) Sam Ratulangi University
Jl. Kampus Unsrat Bahu Manado
Tel. +62-431-852-959
Fax.+62-31-823-705
E-mail: fabian_jm@unsrat.ac.id 

Manuscripts should be typed double spaced (12-pitch font size, times new roman) in a single column format on A4 size paper with 2.5-cm wide margin (top, bottom, left, right). The length of a manuscript should be limited to maximum of 20 pages total (references, figures, tables, appendices, etc. inclusive). All pages should be numbered consecutively.

Deadline of submission:

February edition : first week of December

March edition : first week of February

July edition : first week of April

November edition : first week of August

Language
The language of the journal is English or Indonesia (Abstract should both English and Indonesia).

Style
Manuscripts should be organized in the following order: Title; authors and affiliations; abstract and key words; main body of paper; acknowledgment (where applicable); references; appendices (where applicable). 

Abstract
Abstract should not exceed 150 words. The abstract should state briefly the purpose of the research, the principal results and major conclusions. An abstract is often presented separately from the article, so it must be able to stand alone. For this reason, References should be avoided, but if essential, then cite the author(s) and year(s). Also, non-standard or uncommon abbreviations should be avoided, but if essential they must be defined at their first mention in the abstract itself. so it may become a useful document in an information-retrieval system. Three to ten key words should be included.

Units
SI units must be used throughout in the manuscript. If other units must be used, equivalent SI units shall follow in parentheses. No rigid rules concerning notation or abbreviation need to be observed, but each manuscript should be self-contained as to symbols and units, which should be properly defined. 

Figures and Tables
Photographs, charts, illustrations and diagrams are to be referred to as "Figure(s)". All figures and tables should be placed within the text and identified with consecutive Arabic (not Roman) number in the order they are referred (separate numbers for tables and figures). All lettering, lines and symbols must be of uniform size and cropped to remove irrelevant information. It is better to use several simple tables than one large, complex table. All figures should be clear and suitable for reduction (up to 50% original size). Lettering must be clear and must be large enough to be reduced by the same proportion. All tables and figures must be accompanied by a self-explanatory caption.

Mathematical expressions
Mathematical symbols and formulae should be typed. Particular care should be exercised in identifying all symbols and in avoiding ambiguities. Distinction should be made between the number one (1) and the letter l, or i and between the number zero (0) and the letter o. Equations must be numbered consecutively. Equation numbers should appear in parentheses. All equation number must appear on the right-hand side of the equation and should be referred to within the text. Use following sequence of parenthesis; )] }. 

References
Increased discoverability of research and high quality peer review are ensured by online links to the sources cited. In order to allow us to create links to abstracting and indexing services, please ensure that data provided in the references are correct. Please note that incorrect surnames, journal/book titles, publication year and pagination may prevent link creation. When copying references, please be careful as they may already contain errors.

References to published literatures should be quoted in the text in numerical order. Numerical citation should be typed on the line, not as a superscript, and enclosed in square bracket, [1]. The references should be listed together at the end of the text in consecutive order, with enough information to allow readers to find the cited item. 

Examples:
Reference to a journal publication:

1. Wade, R.L. and Harris, R.B., LOMARK: A Bidding Strategy, Journal of the Construction Division, ASCE, 102(1), 1976, pp. 197-211.

Reference to a book: 
2. Beer, F.P. and Johnston, E.R. Jr., Mechanics of Materials, Second edition, McGraw-Hill, London, 1992.

Reference to chapter in an edited book:
3. Mettam, G.R. and Adams, L.B., How to Prepare an Electronic Version of Your Article, In: Jones, B.S. and Smith, R.Z., Editors, Introduction to the Electronic Age, E-Publishing Inc, New York, 2009.

Reference to a conference paper:
4. Miki, C., Sasaki, E., and Shimozato, T., Seismic Resistance Verification of Fatigue Retrofitted Steel Bridge Bents (A Case Study in the Metropolitan Expressway), Proceedings of the Second International Conference on Urban Earth-quake Engineering, Tokyo, Japan, March 7-8, 2005, pp. 77-84.

Reference to a Standard/Code
5. JIS G 3106, Rolled Steels for Welded Structure, Japanese Industrial Standards Committee, 2008. (In Japanese).

Reference to an online journal 
6. Hardjito, D., Antoni, Wibowo, G.M., and Christianto, D., Pozzolanic Activity Assessment of LUSI Mud in Semi High Volume Pozzolanic Mortar,Materials, 5(9), 2012, pp. 1654-1660, retrieved from http://www.mdpi.com/1996-1944/5/9/1654.

Review
All papers will be reviewed, and the results will be forwarded to the authors ASAP. 

Copyright and Originality
The author should include and sign a paper containing the following information.